No Hot Water but Heating Works: Manchester Causes and Fixes
Few things are more irritating than a cold shower on a winter morning while the radiators are warm to the touch. If you are dealing with no hot water in Manchester but your heating still comes on, the boiler is clearly working, and that is useful information. It tells you the fault is usually in one specific part of the system rather than the whole boiler. This guide explains the causes we see most often in local homes, starts with the diverter valve, and sets out what you can safely check before you need a plumber.
Table of Contents
Quick Takeaways
Key Insight | Explanation |
|---|---|
Heating works but hot water does not | This points to the hot water side of the boiler, such as the diverter valve, heat exchanger or flow sensor, not a general power or ignition failure. |
Test every hot tap | If one tap is cold, the cause may be local, such as a blocked outlet. If every hot tap fails, focus on the boiler or cylinder. |
Check the pressure gauge first | Pressure should sit between 1 and 1.5 bar. Low pressure can affect the boiler's performance, so check it before anything else. |
Cylinder systems have their own controls | If you have a tank or cylinder, check its thermostat and programmer before blaming the boiler. |
Never force a stuck valve | Tapping or manually working a diverter valve can damage the seals and turn a simple replacement into a larger repair. |
Smell gas, stop and get help | Do not try to relight or reset a boiler if you suspect a gas leak. Contact the National Gas Emergency Service and a Gas Safe registered engineer. |
Repeat failures point to replacement | If the same hot water fault keeps returning, the cumulative repair bill can exceed the cost of a newer, more reliable boiler. |
Why Heating Works but Hot Water Does Not
Most boilers in Manchester homes are either combination (combi) boilers or heat-only boilers that feed a hot water cylinder. Both types share one important feature: the central heating circuit and the domestic hot water supply are separate paths that the boiler switches between. When the radiators heat up but hot taps stay cold, the burner is firing and the pump is moving water, so the basic ignition and power are usually fine.
That split makes this fault easier to diagnose than it first appears. A general breakdown, such as a failed ignition or a power loss, tends to stop everything at once. A hot-water-only failure points you towards a short list of components that handle the domestic supply. Working through that list in order often saves a wasted call-out.
How a Combi Boiler Routes Hot Water
Inside a combi, a three-port diverter valve decides whether the flow heads to the radiators or to the plate heat exchanger that warms your mains water on demand. When you open a hot tap, the valve should move across to the domestic side, and the boiler fires to heat the water passing through the exchanger. If the valve sticks in the heating position, the boiler can run perfectly well and still deliver nothing to the taps.
Why Cylinder Systems Fail in a Different Way
In a system boiler or heat-only boiler with a hot water cylinder, the water is heated and stored in the cylinder. A motorised valve sends hot water from the boiler to the cylinder when it is needed. Here the failure is more likely to be a thermostat, a motorised valve, an immersion heater or an airlock in the pipework. Those are different faults from a combi, so the first job is working out which type of system you actually have.

Diverter Valve Faults and How to Spot Them
A diverter valve is driven by a small electric motor, usually called an actuator. Over years of heating and cooling, the motor, the spindle or the internal seals can wear, and the valve can end up stuck between positions. In practice, a stuck diverter valve is one of the first things an engineer checks when a combi delivers heat but no hot water, especially on boilers that are a decade or more old.
Symptoms That Point to the Diverter
The clearest sign is a boiler that fires and runs normally on heating while every hot tap stays cold, even after you have run them for a minute. You may also hear a buzzing or clicking from the boiler casing when you open a hot tap. That sound can mean the actuator is trying to move the valve but cannot finish its travel. Some boilers show a fault code on the display when the valve fails to reach its position.
A useful test is to turn the heating off at the thermostat, then open a hot tap and watch the boiler. If it responds with a sound or a code, write it down for the engineer. If nothing happens at all, the actuator may not be receiving its signal.
Why You Should Not Force It
Some people try to free a stuck valve by tapping the casing or working the actuator by hand. That is a poor idea. You can damage the internal seals, leave the boiler in a worse state and turn a simple part replacement into a more expensive job. Switch the boiler off, leave the valve alone and ask a Gas Safe registered engineer to assess the valve and its actuator. If you want more background on combi systems before you book, our guide to whether a combi boiler suits your Manchester home covers how these systems are laid out.
Heat Exchanger and Flow Faults
When the diverter valve is working, the next suspect is the plate heat exchanger, the component where cold mains water is warmed for your taps. It is built from thin metal plates with narrow channels, and those channels are sensitive to scale. Limescale builds up in hard water areas and gradually narrows the passages, reducing flow until hot water becomes a trickle or stops completely.
Scale Build-Up in the Heat Exchanger
The telltale pattern is hot water that was fine a few months ago and now comes through weakly. Heating is usually unaffected, because the radiator circuit is a separate closed loop. An engineer will typically confirm this by checking flow rates and the condition of the exchanger, then decide whether it can be cleaned or needs replacing based on how far the scale has built up.
Flow Sensors and Cold Mains Filters
Combi boilers use a flow sensor to detect when a hot tap is open and call for heat. If the sensor becomes blocked or fails, the boiler may never fire for hot water, even though the heat exchanger is clean. A blocked filter on the cold mains supply, usually found where the cold water enters the boiler, can cut flow in the same way.
Cleaning a filter is a job some homeowners can manage, but only after isolating the water and power and checking the manual for the correct location. If you are unsure, leave it to a professional. Trying to clear a sensor by taking it apart is a job for an engineer, not a weekend project.
Checks to Make Before You Call an Engineer
Before you pay for a visit, run through the simple checks. Most take minutes, cost nothing and rule out the most common causes of a boiler that works for heating but not for hot water. Work through them in order, and stop immediately if you smell gas or see a fault you are not confident about.
Power, Pressure and Timer Settings
Start with the electrics. If other appliances work but the boiler does not, check the fuse box for a switch that has tripped. Next, look at the pressure gauge. Ideal water pressure sits between 1 and 1.5 bar, and if it reads low, top it up carefully using the filling loop as your manual describes. Power cuts and accidental knocks can also throw the timer out, so confirm the programme still matches your routine.
Reset Buttons and Frozen Condensate Pipes
Some boilers need a reset from time to time. Find the reset button and follow the manufacturer's instructions. If the button sits inside the casing, leave it to a Gas Safe engineer. In cold weather, the condensate pipe can freeze. You can thaw it with warm water or a hot water bottle, but never use boiling water or a naked flame.
If hot water only appears when the heating is on, that is a useful clue. It usually points to a valve or sensor problem rather than a supply issue, and it is worth telling the engineer exactly when the fault shows up. For a wider list of boiler causes, see our guide to central heating not working, with eight causes and fixes.
Pro tip: Before you call, write down whether the cold taps run normally, whether hot water appears with the heating on, what the boiler display shows and when the fault started. That short note often shortens the diagnosis and helps the engineer arrive with the right parts.

Cylinder Systems, Thermostats and Immersion Heaters
If your home has a hot water tank or cylinder, the fault may sit with the cylinder thermostat or programmer rather than the boiler itself. Check that the controls on the tank display the right settings, and adjust them if they do not. These settings are easy to overlook because the boiler can look perfectly normal while the cylinder stays cold.
Cylinder Thermostat and Hot Water Timer
A cylinder thermostat tells the system when the stored water is hot enough. If it is set too low, or it has failed, the water stays lukewarm or cold even though the boiler is fine. Check the dial or digital setting, and confirm any hot water timer is switched on during the hours you need it. Adjusting the setting is safe, but do not open the cylinder's electrical casing yourself.
Motorised Valves and Airlocks
On many cylinder systems, a motorised valve controls whether hot water flows from the boiler to the cylinder. If that valve fails to open, the cylinder never heats, while the radiators carry on working on their own circuit. Air trapped in the pipework, known as an airlock, can also stop hot water reaching the taps. Airlocks often appear after work on the system, and clearing them should be left to a professional if you are not confident with the pipework.
Immersion Heater Checks
An immersion heater gives the cylinder an electric heat source. If the boiler is not firing for hot water but the immersion works, the problem lies on the boiler side. If neither source heats the water, a failed element or thermostat is more likely. Immersion heaters are electrical, so switch off at the consumer unit before touching anything, and leave repairs to a qualified electrician or engineer.
A boiler that heats the radiators but not the taps is giving you a precise clue. The fault is almost always in the hot water path, and the job is to follow that path methodically rather than replacing parts at random.
For cold water problems on the same system, our guide to hot water running cold in Manchester, its causes and who to call explains how to tell a supply issue from a heating fault.
Comparing Your Fix Options
Not every no hot water fault needs the same response. Some you can clear in minutes, some need a repair from a professional, and a few point towards replacing the boiler altogether. The table below compares the three routes most homeowners end up weighing.
Approach | When it fits | What to expect |
|---|---|---|
Homeowner checks | Tripped fuse, timer, pressure, reset button, frozen condensate pipe or cylinder settings | Quick and free. Stop if you smell gas, and call for help if the fault returns straight away. |
Engineer diagnosis and repair | Stuck diverter valve, failed actuator, motorised valve, flow sensor or scaled heat exchanger | A targeted fix on the faulty part. This is usually the sensible route when the rest of the boiler is sound. |
Boiler replacement | Repeated failures, an ageing boiler, or a repair bill that is climbing faster than the boiler's remaining life | A higher upfront cost, but a new boiler brings better reliability and efficiency and a fresh start on the warranty. |
When a Repair Makes Sense
A repair is the right call when the fault is isolated, the boiler is relatively young and the rest of the system is in good condition. A new diverter valve actuator or a descaled heat exchanger is a sensible spend on a boiler that otherwise runs well. Ask the engineer to explain exactly which part failed and why, so you can judge whether it is likely to be an isolated event.
When Replacement Makes More Sense
Replacement becomes the better option when the same hot water fault returns after repairs, when the boiler is near the end of its typical life, or when several parts are failing at once. In those cases, each repair buys you time without addressing the underlying age of the appliance. Compare the cumulative repair spend against the cost of a new unit before you agree to another callout.
A repair that fixes the symptom but not the age of the boiler only buys time. Ask yourself whether the next fault is likely to be the same, and plan your budget around that answer.
When to Call a Manchester Plumber
If the checks in this guide do not restore hot water, get help. If you can smell gas, stop what you are doing, ventilate the property, leave the building and contact the National Gas Emergency Service. For a no hot water fault on a boiler that is otherwise running, a prompt diagnosis from a Gas Safe registered engineer is the right next step.

What to Have Ready for the Engineer
Have your boiler make and model, any fault codes on the display, the approximate age of the system and a note of when the hot water fails. Say at the start whether you have a combi or a cylinder. That single detail shortens the diagnosis and helps the engineer bring the right parts on the first visit.
Pro tip: Ask the engineer to show you the faulty component before it is replaced. Seeing a scaled heat exchanger or a seized actuator makes it much easier to judge whether the repair is sound and whether the fault is likely to come back.
Emergency Callouts Across the Local Area
Neptune Plumbing & Heating is a family-run business based in Leigh, and we cover Wigan, Warrington, Bolton, Manchester, Tyldesley, Lymm, Astley and Atherton. We offer 24-hour emergency callouts, which matters when a cold night leaves the household without hot water or a leak appears alongside a boiler fault. Every job is backed by our full guarantees. If you are facing an urgent problem, our guide to what to do with a 24-hour emergency plumber in Manchester covers what happens after you call.
Frequently Asked Questions
Why is my heating working but my hot water is not?
Your boiler's heating circuit and hot water supply are separate paths. When the radiators heat but the taps stay cold, the fault usually sits in the hot water side, such as a stuck diverter valve, a scaled heat exchanger, a blocked flow sensor, or a cylinder thermostat or motorised valve on a tank system.
Can a diverter valve be repaired, or does it always need replacing?
It depends on the boiler design and what has failed. Sometimes only the actuator motor needs replacing, while in other cases the whole valve is the cleaner fix. An engineer should inspect the valve and make that call based on the parts available for your model.
Is it safe for me to reset my boiler myself?
If the reset button is on the outside of the boiler, you can press it following the manufacturer's instructions. If the button sits inside the casing, leave it to a Gas Safe registered engineer. Never attempt a reset if you smell gas.
How can I tell whether I have a combi boiler or a cylinder system?
A combi boiler heats water on demand and usually has no hot water tank in the loft or airing cupboard. A cylinder system stores hot water in a tank, and you will normally find a cylinder with its own thermostat and timer. If you are unsure, check your boiler manual or ask the engineer to confirm before any work starts.
Do I need a plumber or a Gas Safe engineer for a no hot water fault?
Any work on the boiler itself, including the diverter valve, heat exchanger and gas components, should be carried out by a Gas Safe registered engineer. Pipework, cylinder valves and airlocks may also need a qualified plumber, so ask which trade is needed for the specific fault before the visit.
Have you ever had a boiler that heated the radiators but left you without hot water, and what finally fixed it?






Comments